• Short stroke kit with a low wide hammer (same as on Montado and SASS Ruger). Hammer, pawl, and trigger made from stainless steel. It fits in Old Ruger Vaquero, New Ruger Vaquero, and Super Blackhawk. The hammer has the half cock notch, but no transfer bar anymore. The action is similar to Colt SAA. The kit includes a hammer, trigger, pawl, all springs, and an adjustable hammer stop. Sights can be seen, when the hammer is down. The Short Stroke kit is only for use in Cowboy Action competition! 2013 January Article Shotgun Boogie Ruger SSK When ordering that kit, please let me know the first three digits of the serial number if it's an Old or New Vaquero, and if there is a lock inside the grip frame or not. I need that information to ship you the right pawl and the right hammer stop. While this kit is easily installed, it is not drop-in, it requires fitting by a competent Gunsmith.
  • Reduced lever spring for the new SxS Charles Daly 512

  • The original Uberti springs can be used. You get one right spring, one left spring, two nuts, and two screws with a T8 (Torx) head. Please note: The springs are made for short-stroke versions of Uberti '66 and '73 rifles! To use them on rifles without a short stroke kit, the cam of the lever needs to be modified.
  • Reduced spring for hammer plunger in Ruger single action revolvers

  • Two firing pins, one right and one left for the SxS Charles Daly.

    Pins made from tool steel, hardened and retreted.
  • Fits right and left side. They are lighter then the original springs.

    • You buy two springs.
    • Ready to install.
  • Punch to get the extractor and tab pins out of the Uberti bolt.

    Works on the small .357/.38 Ubert bolts and on the bigger 45LC and 44-40 Uberti bolts. On bolts of the 1873, 1866, and 1860 rifle bolts. The pin punch combines the advantages of a starter and parallel pin punch in one tool.
    • Parallel Pin Punches with Guide Sleeves
    • Heat-treated for the perfect balance of hardness, strength, and durability
    • Industrial quality
    • Manufactured from high-grade tool steel
  • The new and blue aluminum block keeps the bolt stable, when you want to punch the extractor pin out.

    The block can be used on small and large Uberti 73 and 66 rifle bolts. For 357/38 and 45LC, 44-40 etc.
  • These pins fit in Uberti bolts of the 1860, 1866, and 1873 rifles.

    • For small bolts in .357/.38
    • Pins can be used also for the tabs on the .357/.38 bolts.
    • You buy a set of 5 pins.
  • This pin is the right size to punch the pin out of a Ruger, which secures the recoil plate.

    After that cross pin is out, the firing pin, spring, and recoil plate can be punched or pressed out.

    That tool is necessary when you want to change the firing pin spring. This pin punch combines the advantages of a starter and parallel pin punch in one tool.
    • Parallel Pin Punches with Guide Sleeves
    • Heat-treated for the perfect balance of hardness, strength, and durability
    • Industrial quality, made by Rennsteig
    • Manufactured from high-grade tool steel
  • SASS approved in 2020.

    When installing this kit, please be aware that the bolt needs to be modified. You do not have to, nor do I recommend, making modifications to the carrier. All other parts of this kit are drop-in.

    My short stroke kit is not intended to be appreciably shorter than the other ones on the market. The single biggest advantage is the new addition of adjustment screws. Both can be adjusted, when the rifle is assembled! The next difference is the newly configured stop points for the carrier. For this feature, the carrier arm is completely new, designed to hit the perfect high and the low points of the lifter’s travel.  There is no longer any need to adjust the timing here. No welding, filing, or bending is necessary to get perfect stop points for the carrier. With the first screw, you can adjust at what time the carrier arm starts to go up, pushed by the lever. The bolt and the carrier should not touch each other. And even more important, the tab on the bottom of the bolt should not touch the incoming round. If that happens, after a while, the tab will inevitably break. We don’t want to have that problem. With the second screw, you can adjust carrier timing, so that the lever pushes the carrier completely down to the bottom of its travel. This is a feature of the original Winchesters; however, the Uberti 73 rifles don’t do that. You can test that feature thus; when you close the lever, then you can push the carrier about ¼ of an inch up. That adjustment also affects the time at which the lever starts to push the carrier down. One of the problem points of the stock design is this; when the carrier is in its highest position, you can start closing the lever, and while the bolt is still going forward to push the round into the chamber, at the same time the carrier starts to move down. If they touch each other, you will have a problem. To make sure that the carrier and bolt don't touch each other while moving, the bolt needs to be modified. Without that modification, it's not possible to cycle the rifle. I usually do that on my milling machine. I take special care to keep tight tolerances and the finest possible finish.  The tool steel on a Shotgun Boogie Short Stroke Kit has higher strength and toughness than any other short stroke kit on the market. With tight tolerances and quality materials, you avoid a rifle failure, at the worst possible time! Installation of SBGW short stroke kit is possible without filing or welding. And, on top of all of the rest, the timing can be easily readjusted, should the action begin to loosen after usage, as the parts wear in. No more cutting and welding, filing and bending,  and taking the complete rifle apart! Pop off the side plates, adjust the tolerances with the set screws, and you’re done! This is only possible with the SBGW 1873 Short Stroke Kit.

    Attention: This short stroke kit is made only for original Uberti levers. It does not work, when the lever is bent, welded, cut,  or otherwise modified!

  • Ruger Vaquero firing pin tuning spring, which I use in the short stroke kits.

    Works also in Single Six Ruger's, Ruger Super Blackhawks, Ruger Bisley's, etc.

  • Screw for the loading gate of the Uberti lever-action rifle mod 1873.

  • SBGW extended firing pin for Uberti 1860, 1866, and 1873 rifles for all calibers.

    The pin is coming together with the perfect firing pin spring.

  • This kit comes with a mainspring, trigger spring, pawl spring, latch spring, hammer plunger spring, firing pin spring.

    Springs fit in Ruger Wrangler

    While this kit is easily installed, it is not drop-in, it requires fitting by a competent Gunsmith. Tip: A special screwdriver is needed, to get the pig-nose screw of the firing pinout. The diameter of the pins is 1.2mm, the medium distance of the pins is 5mm. A flat screwdriver bit can be modified to fit.
  • One SBGW tuning hammer spring for SKB 100, 200E etc.

    Fits right and left side.

    • With those springs the SKB is easier to open.
    • You buy ONE spring.
    • Ready to install.